O Ring Face Seal Fittings

  • Home /
  • O Ring Face Seal Fittings

O Ring Face Seal Fittings



Flat Face O Ring manufacturer in india with Exceptional sizes, standard, and Quality

 

 

Parker O Ring Face Seal Fittings Suppliers, Supply in 1/8" TO 4" size or custom Size range

In case the O Ring Face Hydraulic Fittings fall out during storage or transit the assembled fitting will then tend to leak. Sometimes it missing Metric O-ring Face Seal Fittings is caught while most of the time it remains unknown thus leading to an increase in the time needed to assemble the product. An O Ring Face Seal Fitting Size Chart defines the size outer diameter and thread size of the standards fittings. As per the O-ring Face Seal Fitting Dimensions a size 14 fitting is said to have ⅞ inch with a thread size between 1-5/16- 12.

O-ring Face Seal Fitting Torque pinched when the ring partially pops out of the groove and is pinched outside the groove. An O ring pinch compromises the connections and leads to a leak. O-ring Face Seal Hydraulic Fittings are said to eliminate leakage at an operating pressure of 6000 psi. VCO O-ring Face Seal Fittings are developed to increase the pace of assembling. It needs to be helium leak tested at the rate of 4X 10 - 5 std cm3. O-ring Face Seal Hydraulic Hose Fittings has a straight thread and a machined groove in the face of the male fitting. The Female Vco O-ring Face Seal Fittings is compressed towards the flat face fitting for protection against leakage. 

 

BRAND NAME TU-LOK
VALVE SIZE 1/8" TO 4" 
THREAD NPT, BSPP, BSPT, METRIC, UNF
END CONNECTION THREADED, BUTT WELD, SOCKET WELD
PRESSURE RATING 1500 PSI, 3000 PSI, 6000 PSI, 10000 PSI, 15000 PSI, 20000 PSI
MEDIA  HYDRAULIC OIL, AIR, WATER, GAS, STEAM, HOT WATER , COLD WATER , SEA WATER , CHEMICAL
SEAL MATERIAL VITON, NITRILE
MEDIA TEMPERATURE (-120* C TO 500*C ) RANGE AS PER PRESSURE
BODY TYPE BAR STOCK, FORGED
MATERIAL SS 316, SS 304, BRASS, SS 316 TI, CS, COPPER, SUPER DUPLEX, INCONEL, DUPLEX, HASTELLOY, MONEL, ALLOY 20, SMO 254, 904L, TITANIUM & ALL OTHER ALLOYS

 

Hydraulic systems that have higher operating pressure often experienced the problem of leakage. To solve this problem O Ring Face Seal Fittings were invented. O Ring Face Seal is said to be more reliable when compared to metal-to-metal seal. Flat Face O Ring offers zero clearance for easy plumbing. Flat Face O Ring Fittings offer resistance from over torquing that eliminates damage from overtightening. Parker O Ring Face Seal Fittings also reduce the loosening that is caused due to vibration. o ring face seal fittings manufacturers in India offer these elastomeric seals for unlimited reusability

O Ring Face Seal Fittings

 

Description Price list
Customerized Hydraulic Elbow Fittings with O-Ring Face Seal US $ 0.2-3 / Piece
304 O-Ring Face Seal DIN 2353 Compression Fittings for Hydraulic. US $ 0.99-12.99 / Piece
Stainless Steel 12 Vco O-Ring Face Seal Fitting US $ 0.99-12.99 / Piece
Metric Thread O-Ring Face Seal Fittings 1e9
US $ 0.2-1.5 / Piece
Hydraulic Three Way Tee Fittings with O-Ring Face Seal Orfs US $ 0.2-2 / Piece
Hydraulic Tube & Pipe Fittings with O-Ring Face Seal
US $ 0.2-1 / Piece
O-Ring Face Seal Orfs Straight Steel Fitting
US $ 0.6-0.98 / Piece
Stainless Steel Metric Thread O-Ring Face Seal Fittings Hydraulic Fittings
US $ 0.2-0.99 / Piece

 

 

If you need O Ring Face Hydraulic Fittings We can supply in NPT, BSPP, BSPT, METRIC, UNF thread

 

MALE ORFS TO MALE NPT ADAPTER

MALE ORFS TO MALE NPT ADAPTER

ORFS BULKHEAD ADAPTER

ORFS BULKHEAD ADAPTER

ORFS MALE ELBOW

ORFS MALE ELBOW

ORFS MALE PLUG

ORFS MALE PLUG

SAE 90 DEGREE ORFS ELBOW

SAE 90 DEGREE ORFS ELBOW

 

Nominal Pipe OD (inch) SAE Dash Size Fittings w/ NPTF Pipe Threads (psi) Thread Size NPTF & NPSM Fittings w/ NPSM Female Swivel (psi)
1/8 -02 5,000 1/8 27 5,000
1/4 -04 4,000 1/4 18 5,000
3/8 -06 3,000 3/8 18 4,000
1/2 -08 3,000 1/2 14 3,500
3/4 -12 2,500 3/4 14 2,250
1 -16 2,000 1 11-1/2 2,000
1-1/4 -20 1,150 1-1/4 11-1/2 1,625
1-1/2 -24 1,000 1-1/2 11-1/2 1,250
2 -32 1,000 2 11-1/2 1,125

 

Tube Size Foot – Pounds (ft-lbs) Thread Size Newton – Meters (Nm)
-04 10-12 9/16 18 14-16
-06 18-20 11/16 16 24-27
-08 32-35 13/16 16 43-47
-10 46-50 1 14 60-68
-12 65-70 1-3/16 12 90-95
-14 65-70 1-3/16 12 90-95
-16 92-100 1-7/16 12 125-135
-20 125-140 1-11/16 12 170-190
-24 150-165 2 12 200-225

 

  • oil and gas
  • construction equipment
  • Hydraulic fluid and gas handling connections
  • mining and the high performance industrial markets
  • agricultural equipment

 

We have a large inventory of Metric and Female Vco O-ring Face Seal Fittings with 3000/ 6000/ 10000/ 15000/ 20000 PSI Pressure rating

 

ORS Tube Size CS Nominal Dash # OD Nominal ID Inch ID Nominal CS Inch
-4 1/16 011 7/16 0.0301 5/16 0.007
-6 1/16 012 1/2 0.0364 3/8 0.007
-8 1/16 014 5/8 0.0489 1/2 0.007
-10 1/16 016 3/4 0.0614 5/8 0.007
-12 1/16 018 7/8 0.0739 3/4 0.007
-16 1/16 021 1-1/16 0.0926 15/16 0.007
-20 1/16 025 1-5/16 1.0176 1-3/16 0.007
-24 1/16 029 1-5/8 1.0489 1-1/2 0.007

 

SAE Dash Size Thread Size Nominal Tube OD (inch) ORFS Fittings
-04 9/16 18 UNF 1/4 6,000
-05 5/8 18 UNF 5/16 6,000
-06 11/16 16 UNF 3/8 6,000
-08 13/16 16 UNF 1/2 6,000
-10 1 14 UNF 5/8 6,000
-12 1-3/16 12 UN 3/4 6,000
-14 1-5/16 12 UN 7/8 6,000
-16 1-7/16 12 UN 1 6,000
-20 1-11/16 12 UN 1-1/4 4,000
-24 2 12 UN 1-1/2 4,000

 

Design of O Ring Face Seal

 

AS 568A SERIES GLAND  CORNER RADII O-RING- CROSS SECTION GLAND DEPTH
(H)
GLAND WIDTH
(W)
(R1) (R2) TOL +/- NOM NOM TOL+/- NOM TOL+/-
000 0.0010 0.0005 0.0003 0.0070 0.0052 0.0002 0.0084 0.0002
-100 0.0010 0.0005 0.0003 0.0103 0.0078 0.0003 0.0121 0.0003
-200 0.0018 0.0005 0.0004 0.0139 0.0106 0.0003 0.0160 0.0003
-300 0.0028 0.0005 0.0005 0.0210 0.0164 0.0004 0.0240 0.0003
-400 0.0028 0.0005 0.0006 0.0275 0.0215 0.0004 0.0310 0.0003

 

Flat Face O-Ring Thread Specifications
Size Thread Size Tube OD (inch)
4 9/16 - 18 1/4
6 11/16 - 16 3/8
8 13/16 - 16 1/2
10 1 - 14 5/8
12 1-3/16 - 12 3/4
14 1-5/16 - 12 7/8
16 1-7/16 - 12 1
20 1-11/16 - 12 1-1/4
24 2 - 12 1-1/2
32 2-1/2 - 12 2

 

find here O-ring Face Seal Fitting Dimensions, Torque and Size chart online

 

Groove design Flat Face O Ring

 

SAE J1453 O-Ring Face Seal (ORFS)
Dash
Size
Thread Inch
Size
Female
Thread
I.D
inches
Male
Thread
OD
inches
Male
Thread
OD
mm
Female
Thread
I.D
mm
4 9/16-18 1/4 .0051 .0056 14.002 12.009
6 11/16-16 3/8 .0063 .0068 17.003 16.000
8 13/16-16 1/2 .0075 .0081 20.006 19.000
10 1-14 5/8 .0093 1.0000 25.004 23.006
12 1 13/16-12 3/4 1.0010 1.0018 30.000 27.008
16 1 7/16-12 1 1.0036 1.0044 36.006 34.005
20 1 11/16-12 1 1/4 1.0060 1.0068 42.007 40.006
24 2 -12 1 1/2 1.0092 2.0000 50.008 48.008

 

Flange/Face Seal

Flange/Face Seal

AS568 Series Gland Depth (D) Gland Width (W) Vacuum & Gases O-Ring Cross-Section Gland Width (W) Liquids Squeeze Gland Corner Radii
Nominal TOL (+/-) Nominal TOL (+/-) Nominal TOL (+/-) Actual Percent R1 R2
-0XX .0055-0.0057 0.0084 0.0003 0.0070 0.0003 0.0103 0.0002 .0010-.0018 15%-25% 0.0010 0.0005
-1XX .0088-.0090 0.0121 0.0003 0.0103 0.0004 0.0140 0.0003 .0010-.0018 10%-17% 0.0010 0.0005
-2XX .0121-.0123 0.0160 0.0003 0.0139 0.0004 0.0180 0.0003 .0012-.0022 9%-16% 0.0018 0.0005
-3XX .0185-.0188 0.0240 0.0003 0.0210 0.0005 0.0280 0.0003 .0017-.0030 8%-14% 0.0028 0.0005
-4XX .0237-.0240 0.0310 0.0003 0.0275 0.0006 0.0352 0.0003 .0029-.0044 11%-16% 0.0028 0.0005

 

Static Gland Seal

Static Gland Seal

AS568 Series Gland Depth (D) O-Ring Cross-Section Gland Width (W) Squeeze Gap (H) Gland Corner Radii
Nominal TOL (+/-) Nominal TOL (+/-) w/ 1 Backup Ring w/ 2 Backup Rings Actual Percent MAX R1 R2
-0XX .0050-0.0052 0.0070 0.0003 0.0095 0.0002 0.0140 0.0207 .0015-.0023 22%-32% 0.0002 0.0007 0.0005
-1XX .0081-.0083 0.0103 0.0004 0.0142 0.0003 0.0173 0.0240 .0017-.0025 17%-24% 0.0002 0.0007 0.0005
-2XX .0111-.0113 0.0139 0.0004 0.0189 0.0003 0.0210 0.0277 .0022-.0032 16%-23% 0.0002 0.0017 0.0005
-3XX .0170-.0173 0.0210 0.0005 0.0283 0.0003 0.0313 0.0412 .0032-.0045 15%-21% 0.0003 0.0027 0.0005
-4XX .0226-.0229 0.0275 0.0006 0.0377 0.0003 0.0410 0.0540 .0040-.0055 15%-20% 0.0003 0.0027 0.0005

 

Dynamic Gland Seal

Dynamic Gland Seal

AS568 Series Gland Depth (D) O-Ring Cross-Section Gland Width (W) Squeeze Gap (H) Gland Corner Radii
Nominal TOL (+/-) Nominal TOL (+/-) w/ 1 Backup Ring w/ 2 Backup Rings Actual Percent MAX R1 R2
-0XX .0055-0.0057 0.0070 0.0003 0.0095 0.0002 0.0140 0.0207 .0010-.0018 15%-25% 0.0002 0.0007 0.0005
-1XX .0088-.0090 0.0103 0.0004 0.0142 0.0003 0.0173 0.0240 .0010-.0018 10%-17% 0.0002 0.0007 0.0005
-2XX .0121-.0123 0.0139 0.0004 0.0189 0.0003 0.0210 0.0277 .0012-.0022 9%-16% 0.0002 0.0017 0.0005
-3XX .0185-.0188 0.0210 0.0005 0.0283 0.0003 0.0313 0.0412 .0017-.0030 8%-14% 0.0003 0.0027 0.0005
-4XX .0237-.0240 0.0275 0.0006 0.0377 0.0003 0.0410 0.0540 .0029-.0044 11%-16% 0.0003 0.0027 0.0005

 

Smaller Cross-Section O-Rings Advantages

  • Most cost-effective if the design uses expensive elastomers such as FKM or FFKM
  • Compact and lighter-weight o-ring
  • Reduced machining of grooves

Larger Cross-Section O-Rings Advantages

  • Smaller required squeeze to create a seal which reduces compression set issues
  • Greater tolerances variations in the machined groove while maintaining acceptable compression squeeze

 

O-Ring Gland Dimensions Calculation

 

Philippines, Dammam -KSA, Belgium, Indonesia Parker O Ring Face Seal Fittings
Europe, Qatar, Thailand, France O Ring Face Hydraulic Fittings
Thailand, Czechia,  Malaysia, Germany Metric O-ring Face Seal Fittings
Bangladesh, Malaysia, Finland, USA O-ring Face Seal Hydraulic Fittings
Kuwait, South Africa, Brazil, Saudi Arabia (KSA) Vco O-ring Face Seal Fittings
Singapore, Bahrain, Singapore, South Africa O-ring Face Seal Hydraulic Hose Fittings
UK, Philippines, Nigeria, Australia Female Vco O-ring Face Seal Fittings
Hong Kong, Oman, UAE, Malaysia O Ring Face Seal Fittings
Iran, Chile, Singapore, Italy Flat Face O Ring
Norway, United Arab Emirates (UAE),  Malaysia, Turkey Flat Face O Ring Fittings