ISO 6162 Flange

  • Home /
  • ISO 6162 Flange

ISO 6162 FLANGE



Flange SAE ISO 6162-1 manufacturer in India with SAE J518 C SAE other side Connection

 

A surge in pressure above the normal rating will lead to the Iso 6162-2 Flange connection to retain hydraulic fluid. This fact needs to be considered while designing the hydraulic system. Iso 6162 Sae Flange connections are available in the size range of ½ inch to 5 inches.  The pressure rating of the SAE J518 Flange is up to 420 bars and the outer diameter ranges between 12 mm to 140 mm. Iso 6162-1 Flange Dimensions are suitable for hydraulic fluid power flange connection with one piece flange clamp or split with the use of metric or inch screw. 

Iso 6162-2 Flange Dimensions ensures better performance even if the installation space is tight due to the lower torque for tightening a Flange Sae Iso 6162-1 screw a lower torque is required when compared to equivalent connection thread. The connection capability of the tube is up to 5 inches external diameter. Iso 6162 Flange Dimensions provides only 1 sealing point between the flange joint and the tube fitting. The working principle Iso 6162-1/-2 flange is based on embedding a compressible seal between 2 faces that are orchestrated parallel to one another.

 

Table of Content

 

ISO 6162 Split Flange Suppliers, Have difficulty to SAE J518 Flange in tough sizes ? Call Tu-lok now

 

Specification format of ISO 6162 Split Flange

BRAND NAME TU-LOK
VALVE SIZE 1/8" TO 4" 
THREAD NPT, BSPP, BSPT, METRIC, UNF
END CONNECTION THREADED, BUTT WELD, SOCKET WELD
OTHER SIDE CONNECTION SAE J518 C SAE FLANGES
PRESSURE RATING 3000 PSI (CODE 61) & 6000 PSI (CODE 62)
MEDIA  HYDRAULIC OIL, AIR, WATER, GAS, STEAM, HOT WATER , COLD WATER , SEA WATER , CHEMICAL
MEDIA TEMPERATURE (-120* C TO 500*C ) RANGE AS PER PRESSURE
BODY TYPE BAR STOCK, FORGED
MATERIAL SS 316, SS 304, BRASS, SS 316 TI, CS, COPPER, SUPER DUPLEX, INCONEL, DUPLEX, HASTELLOY, MONEL, ALLOY 20, SMO 254, 904L, TITANIUM & ALL OTHER ALLOYS

 

What is ISO 6162 Flange ?

Flanges are used to connect or terminate a piping system and are available in various standards. One such type is the Iso 6162 Flange. It gives the iso 6162 flange manufacturers in India the general and dimensional specification of flange head, ports, one piece flange clamps, split flange clamps, and mounting surface for them. Flange SAE ISO 6162-1 is designed with the intention to be used in the hydraulic system. Iso 6162 Split Flange is mostly used in industrial and commercial products where it is necessary to avoid the use of threaded connectors. 

ISO 6162 FLANGE

 

Price list of ISO 6162-2 Flange

Description Price
ISO 6162 Hydraulic Flange
 US $ 0.9-1.1 / Piece
SAE Socket Weld ISO 6162.2 Heavy 6000psi Flange/ Carbon Steel SAE J518
 US $ 1.6-78.8 / Piece
Carbon Steel SAE Socket Weld 1/2" ISO 6162 3000 Psi 6000 Psi Flange/ Hydraulic Parts Connector Adapter US $ 1-888 / Piece
ISO 6162.2 Heavy 6000psi SAE Socket Weld Flange Coupling
 US $ 3.2-158 / Piece
Hydraulic Thread 2" ISO 6162 3000 Psi Pipe Flange
 US $ 0.5-8 / Piece

 

Supply ISO 6162 SAE Flange in all sizes and 3000 PSI (Code 61) & 6000 PSI (Code 62) Pressure Rating

 

ISO 6162 Flange Manufacturer in india

90 DEGREE ELBOW FLANGE ADAPTER

90 DEGREE ELBOW FLANGE ADAPTER

JIC 37 DEGRRE ELBOW FLANGE ADAPTER

JIC 37 DEGRRE ELBOW FLANGE ADAPTER

MALE ORFS FLANGE ADAPTER FITTING

MALE ORFS FLANGE ADAPTER FITTING

METRIC MALE BITE TYPE FLANGE ADAPTER

METRIC MALE BITE TYPE FLANGE ADAPTER

ISO 6162 FLANGE

ISO 6162 FLANGE

ISO 6162 SPLIT FLANGE

ISO 6162 SPLIT FLANGE

 

Dimensions chart of ISO 6162-1 Flange

Dimensions chart of ISO 6162-1 Flange

 

Nominal Flange

2.05 to 31.05 MPa Series1) (SAE Code 61)

 

O-Rings3)

Size

Clamping Screws

Flange Half and Bolt Pattern

 

D3

Screw Holes

 

 

Parker

 

Type I

Type II2) (SAE J518)

C

J

W

Y

L5

L6

ISO 3601-1

O-Ring

(in)

(mm)

Thread

t1 Min.0 depth

Thread (UNC)

t1 Min.0 depth

± 0.025

max.0

min.0

±0.025

Ref.0

 

 

ID x Section

Size

1/2

13

M8 x 1.025

12.05

5/16 - 18

24

38.01

54.09

53.01

17.05

46

13

19

19 x 3.055

2-210

3/4

19

M10 x 1.05

16.05

3/8 - 16

22

47.06

65.08

64.03

22.03

52

14

22

25 x 3.055

2-214

1

25

M10 x 1.05

14.05

3/8 - 16

22

52.04

70.06

69.01

26.02

59

16

22

32.05 x 3.055

2-219

1 1/4

32

M10 x 1.05

16.05

7/16 - 14

28

58.07

80.03

78.05

30.02

73

144)

24

37.05 x 3.055

2-222

1 1/2

38

M12 x 1.075

19.05

1/2 - 13

27

69.09

94.05

93.00

35.07

83

16

25

47.05 x 3.055

2-225

2

51

M12 x 1.075

19.05

1/2 - 13

27

77.08

103.01

100.01

42.09

97

16

26

56 x 3.055

2-228

2 1/2

64

M12 x 1.075

21.05

1/2 - 13

30

88.09

115.08

112.08

50.08

109

19

38

69 x 3.055

2-232

3

76

M16 x 2

28.05

5/8 - 11

30

106.04

136.07

133.04

61.09

131

22

41

85 x 3.055

2-237

3 1/2

89

M16 x 2

28.05

5/8 - 11

33

120.07

153.09

150.09

69.09

140

22

28

97.05 x 3.055

2-241

4

102

M16 x 2

25.05

5/8 - 11

30

130.02

163.06

160.03

77.08

152

25

35

112 x 3.055

2-245

5

127

M16 x 2

27.05

5/8 - 11

33

152.04

182.06

185.07

92.01

181

28

41

136 x 3.055

2-253

 

Nominal Flange
Size D3

40 MPa Series1)
(SAE Code 62)

 

O-Rings3)

Clamping Screws
Screw Holes

Flange Half and Bolt Pattern

 

ISO 3601-1
ID x Section

Parker O-Ring
Size

Type I

Type II2) (SAE J518)

C
± 0.025

J

W
±0.025

Y
Ref.0

L5

L6

(in)

(mm)

Thread

t1 Min.0 depth

Thread (UNC)

t1 Min.0 depth

max.0

min.0

1/2
3/4
1

13
19
25

M8 x 1.025
M10 x 1.05
M12 x 1.075

14.05
16.05
21.05

5/16 - 18
3/8 - 16
7/16 - 14

21
24
27

40.05
50.08
57.02

57.02
72.01
81.08

55.06
70.06
80.03

18.02
23.08
27.08

48
60
70

16
19
24

22
28
33

19 x 3.055
25 x 3.055
32.05 x 3.055

2-210
2-214
2-219

1 1/4
1 1/2
2

32
38
51

M12 x 1.075
M16 x 2
M20 x 2.05

18.05
25.05
33.05

1/2 - 13
5/8 - 11
3/4 - 10

25
35
38

66.06
79.03
96.08

96.00
114.03
134.09

94.05
111.03
131.08

31.08
36.05
44.05

78
95
114

27
30
37

38
43
52

37.05 x 3.055
47.05 x 3.055
56 x 3.055

2-222
2-225
2-228

 

ISO 6162-1 vs SAE J518-1 code 61 flange

ISO 6162-1 SAE J518-1 code 61
ISO 6162-1 standard is for Hydraulic liquid power Flange associations with part or metric or one-piece flange clamps and inch screws for utilize at pressures of DN 13 - DN 127, 3,5 MPa (35 bar) - 35 MPa (350 bar) SAE J518-1 standard is Hydraulic Flanged Pipe, Tube and Hose Associations, 4-Screw Flange Association 3.5 MPa - 35 MPa (Code 61 ).

 

3000 PSI Series code 6162 flange dimensions

DN PIPE SIZE Фd Фd1 Фd2 1 L h h1 B B1 T A '0' RING SIZE HEX.0HD.0CAP SCREW SIZE
INCH MM ODxWT AFH
AFU
1/2" 13 20.00x3.00 20 14.00 30.02 30 60 13 19 54 46 38.01 17.05 18.064x3.053 M8x25/
5/16"_18UNC x 11/4"
22.00x2.00 22 18.00
21.03x2.06 22 16.00
      M8x40/
5/16"_18UNC x 11/2"
     
     
3/4" 19 22 x 2.00 22 18.00 38.01 35 70 14 22 65 52 47.06 22.03 24.099 x 3.053 M 10x30/
3/8"_16UNC x 11/4"
25.00x3.00 25 19.00
26.09x3.06 27 19.05
      M 10x40/
3/8"_16UNC x 11/2"
     
     
1" 25 30.00x4.00 30 22.00 44.04 40 80 16 24 70 59 52.04 26.02 32.092 x 3.053 M 10x30/
3/8"_16UNC x 11/4"
35.00x4.00 35 27.00
33.07x3.02 34 27.00
38.00x2.05 38 33.00 M 10x45/
3/8"_16UNC x 2"
38.00x4.00 38 30.00
     
11/4" 32 38.00x4.00 38 30.00 50.08 45 90 16 22 80 73 58.07 30.02 37.069x3.053 M 10x30/
7/16"_14UNC x 11/2"
42.00x3.00 42 36.00
42.03x3.02 43 36.00
42.04x5.06 43 31.02 M 10x50 /
7/16"_14UNC x 2"
     
     
11/2" 38 38.00x4.00 38 30.00 60.03 50 100 16 25 94 83 69.09 35.07 47.022x3.053 M 12x35/
1/2"_13UNC x 11/2"
42.00x3.00 42 36.00
48.03x4.05 49 39.00
48.03x6.03 49 35.05 M 12x50/
1/2"_13UNC x 2"
     
     
2" 51 42.00x3.00 42 36.00 71.04 60 120 16 26 102 97 77.08 42.09 56.074 x 3.053 M 12x35/
1/2"_13UNC x 11/2"
42.03x3.02 43 36.00
48.03x3.02 49 42.00
60.03x5.06 61 49.00
60.03x8.00 61 44.00 M12x50/
1/2"_13UNC x 2"

 

SAE J518/ISO 6162 Flange Advantages

  • Low tightening torques also mean using small flat wrenches, ensuring better performance where the installation space is tight.
  • For tightening the screws, slightly lower tightening torques compared with the equivalent connection threads are required.
  • Connection capacity of tubes up to 5" external diameter (ISO 6162-1, SAE J518 code).
  • Just one sealing point between fitting the tube/ pipe to the flanged joint.
  • Application up to 420 bars (6000 PSI) for flange sizes 1/2" to 2" (ISO 6162-2, SAE J518 code 62).
  • Easy to remove

 

6000 PSI Series ISO 6162-2 Split flange dimensions

SPLIT FLANGES ACCORDING TO THE ISO 6162-2 / SAE 6000
Part N°   DN PN bar1 F Ø T Ø J Ø D U GG/2 O Q FF/2 Bolts
Metric UNC
DB-6000-1/2"-M/U   13 400 7.2 8.7 24.6 32.5 16 9.1 56.5 40.5 23.6 8 5/16"
DB-6000-3/4"-M/U   19 400 8.2 10.5 32.5 42 19 11.9 71 50.8 30 10 3/8"
DB-6000-1"-U   25 400 9 12 38.8 48.4 24 13.85 81 57.1 34.8 - 7/16"
DB-6000-1"-M   25 400 9 13 38.8 48.4 24 13.85 81 57.1 34.8 12 -
DB-6000-1"1/4-U / ISO*   32 400 9.8 13.5 44.5 54.8 27 15.85 95 66.7 38.6 12 1/2"
DB-6000-1"1/4-M   32 400 9.8 15 44.5 54.8 27 15.85 95 66.7 38.6 14 -
DB-6000-1"1/2-M/U   38 400 12 17 51.6 64.3 30 18.25 113 79.4 47.5 16 5/8"
DB-6000-2"-M / U / ISO   51 400 12 21 67.6 80.2 37 22.2 133 96.8 56.9 20 3/4"

 

We Guarantee Fastest Delivery of ISO 6162-2 Flange with All Documents Including Mill Certificate

 

Step to protect Flange SAE ISO 6162-1

  • Test Flanges ISO 6162 / 6164 : Galvanizing-bichromating
  • Square flanges : Phosphatization or oiling
  • Flanges and Split Flanges ISO 6162 / SAE : Galvanizing-bichromating
  • Threaded flanged head : Galvanizing-bichromating
  • Flanged head to be welded and plug flange : Oiling or Phosphatization
  • Connection Blocks : Oiling
  • Nuts and bolts : Burnishing

 

ISO 6162-1/-2 Tightening Torque

Metric screw

Dia. screws M 8 M 6 M 12 M 10 M 16 M 14 M 20 M 24 M 18 M 22 M 27
Couple Maxi da Nm 3,2 1 13 7 23 14,9 45 71 32 61 110

 

UNC screw

Dia. screws 3/4" 3/8" 5/16" 1/2" 7/16" 5/8"
Couple Maxi da Nm 49 6,3 3,5 15,6 10 30

 

Working Principle of ISO 6162 Flange

  • This is often based on embeddings a compressible seal between 2 faces orchestrated parallel to one another, and firmly held, squeezing against one another be implies of bolted flanges.
  • The seal is precisely centred by implies of a circular groove in which it is housed. For union get together flanges, the two faces will be flanged head conclusion (one with a seal, the other without).
  • For port get together flanges, the two faces will be on one hand the flanged head en holding the seal, and on the other the outside portion of the hydraulic machine to be seal

 

Seal Size of ISO 6162 flange

0'RINGS
DN Ø int. x Ø tore Part N° Assembly
3/8" 17.12 X 2.62 JT 1712-262 3000 - PN 250/400
1/2" 18.64 X 3.53 JT 1864-353 3000/6000 - PN 250/400
3/4" 24.99 X 3.53 JT 2499-353 3000/6000 - PN 250/400
1" 32.92 X 3.53 JT 3292-353 3000/6000 - PN 250/400
1"1/4 37.69 X 3.53 JT 3769-353 3000/6000 - PN 250/400
1"1/2 47.22 X 3.53 JT 47.22-353 3000/6000 - PN 250/400
2" 56.74 X 3.53 JT 56.74-353 3000/6000 - PN 250/400
2"1/2 69.44 X 3.53 JT 6944-353 3000 PSI - PN 250
2"1/2 69.22 X 5.33 JT 6922-533 PN 400
3" 85.32 X 3.53 JT 8532-353 3000 PSI - PN 250
3" 75.57 X 5.33 JT 7557-533 PN 400
3"1/2 98.02 X 3.53 JT 9802-353 3000 PSI
3"1/2 85.32 X 3.53 JT 8532-353 PN 250
3"1/2 85.09 X 5.33 JT 8509-533 PN 400
4" 110.72 X 3.53 JT 11072-353 3000 PSI
4" 98.02 X 3.53 JT 9802-353 PN 250
4" 88.27 X 5.33 JT 8827-533 PN 400

 

buy ISO 6162 Flange with media temperature (-120* C TO 500*C) ? find here ISO 6162-1/-2 Flanges Dimension

 

ISO 6162 Split Flange stock list

Series
Flage Size
 Face Type Material Port Style Port Size
SAE J518 C62 / ISO 6162-2 1/2 O-ring Face Carbon Steel Flange Plug NA
SAE J518 C62 / ISO 6162-2 3/4 O-ring Face Carbon Steel Flange Plug NA
SAE J518 C62 / ISO 6162-2 1 O-ring Face Carbon Steel Flange Plug NA
SAE J518 C62 / ISO 6162-2 1 1/4 O-ring Face Carbon Steel Flange Plug NA
SAE J518 C62 / ISO 6162-2 1 1/2 O-ring Face Carbon Steel Flange Plug NA
SAE J518 C62 / ISO 6162-2 2 O-ring Face Carbon Steel Flange Plug NA
SAE J518 C62 / ISO 6162-2 1/2 None Carbon Steel Flange Clamp 1/2
SAE J518 C62 / ISO 6162-2 1/2 None Carbon Steel Flange Clamp 1/2
SAE J518 C62 / ISO 6162-2 3/4 None Carbon Steel Flange Clamp 3/4
SAE J518 C62 / ISO 6162-2 3/4 None Carbon Steel Flange Clamp 3/4
SAE J518 C62 / ISO 6162-2 1 None Carbon Steel Flange Clamp 1
SAE J518 C62 / ISO 6162-2 1 None Carbon Steel Flange Clamp 1
SAE J518 C62 / ISO 6162-2 1 1/4 None Carbon Steel Flange Clamp 1 1/4
SAE J518 C62 / ISO 6162-2 1 1/4 None Carbon Steel Flange Clamp 1 1/4
SAE J518 C62 / ISO 6162-2 1 1/2 None Carbon Steel Flange Clamp 1 1/2
SAE J518 C62 / ISO 6162-2 1 1/2 None Carbon Steel Flange Clamp 1 1/2
SAE J518 C62 / ISO 6162-2 2 None Carbon Steel Flange Clamp 2
SAE J518 C62 / ISO 6162-2 2 None Carbon Steel Flange Clamp 2
SAE J518 C62 / ISO 6162-2 1/2 None Carbon Steel Flange Clamp 1/2
SAE J518 C62 / ISO 6162-2 3/4 None Carbon Steel Flange Clamp 3/4
SAE J518 C62 / ISO 6162-2 1 None Carbon Steel Flange Clamp 1
SAE J518 C62 / ISO 6162-2 1 1/4 None Carbon Steel Flange Clamp 1 1/4
SAE J518 C62 / ISO 6162-2 1 1/2 None Carbon Steel Flange Clamp 1 1/2
SAE J518 C62 / ISO 6162-2 2 None Carbon Steel Flange Clamp 2
SAE J518 C62 / ISO 6162-2 1/2 O-ring Face Carbon Steel Socket Weld for Pipe 1/2

 

Features of Flange SAE ISO 6162-1

  • Silver Trivalent finish for high corrosion resistance
  • Forged carbon steel construction
  • Available in forged 316L stainless
  • Kits include two flange halves, bolt kit and a Buna o-ring

 

Normalization of ISO 6162-2 Flange

SAE TYPE RECTANGULAR FLANGES AND FLANGED
HEAD TO BE WELDED		 NORM ISO
(NORM AFNOR)
NORM U.S.A.		 ISO 6162-1 and 2 to 2002
( NF E 48-055 12/86 )
SAE J 518
CETOP AND SIDERURGIE TYPE SQUARE FLANGES AND
FLANGED HEAD TO BE WELDED		 AFNOR
RECOMMENDATION		 NF E 48-054 12/98
CETOP RP 63 H
ISO 6164 05/94
METRIC BOLTS AND NUTS AFNOR
DIN
U.S.A.		 NF EN ISO 4762 12/97
912
According to American standard
0-RINGS USA
AFNOR		 SAE J 515
NF T 47 501 04/98

 

Machining of ISO 6162 Split Flange

Flanges Flanges head
Untreated external surfaces
Internal face Ra = 6,3
Reaming Ra = 6,3		 All external sections Ra = 6.3
Pass Ra = 6,3
Bearing surfaces of seals and grooves Ra = 1,6

 

Take the reference of our quality and timely delivery from our clients in following cities

Qatar, Thailand, Europe, France Stainless Steel ISO 6162.1 Light 3000psi SAE Female Thread Flange
Dammam -KSA, Belgium, Philippines, Indonesia ISO 6162.1 Split Flange Halves with Butt Weld Head
Malaysia, Finland, Bangladesh, USA Carbon Steel Galvanized 2-1/2" ISO 6162 6000psi Hydraulic Split Halves Flange
Czechia, Malaysia, Thailand, Germany ISO 6162-1 90 Elow Metric Male Bite Type/S-Series Flange/ Adapter
Bahrain, Singapore, Singapore, South Africa Carbon Steel Socket Weld 1" ISO 6162 Hydraulic Pipe Flange
South Africa, Brazil, Kuwait, Saudi Arabia (KSA) Stainless Steel SAE 5" ISO 6162 Split Halves Flange
Oman, UAE, Hong Kong, Malaysia ISO 6162-1 Metric Male Bite Type L-Series Flange
United Kingdom -UK, UAE, Malaysia, Europe Carbon Steel 3" ISO 6162 Code 62 Hydraulic Socket Weld Flange
Philippines, Nigeria, UK, Australia Carbon Steel SAE 1-1/2" ISO 6162 Socket Weld Elbow Flange
United Arab Emirates (UAE), Malaysia, Norway, Turkey Stainless Steel ISO 6162.2 Heavy 6000psi Butt Weld SAE Flange Coupling with Flange Head
Chile, Singapore, Iran, Italy ISO 6162.1 Light SAE carbon Steel Closed Flange
Egypt, UK, Mexico, Spain Carbon Steel ISO 6162 Hydraulic Socket Weld Flange
UK, Ellington -United States, Poland, Canada Carbon Steel 3" ISO 6162 Butt Weld Hydraulic Pipe Flange

 

 

 

Pipe Fittings